TheCoatingStore.com

Search:

Type: Posts; User: 67flh

Search: Search took 0.00 seconds.

  1. Thread: Rookie errors

    by 67flh
    Replies
    2
    Views
    153

    Rookie errors

    I am painting some fenders for a garden tractor and did not have sense enough to quit laying on paint and have some serious runs. It is an enamel paint with a hardener added. Can I just sand...
  2. Replies
    0
    Views
    90

    Hobby Air Respirator

    I am a firm believer in the use of PPE and when I started researching the use of hardeners in paint I was very surprised at the hazards involved. I was even more surprised by the amount of people...
  3. Thread: Imperfections

    by 67flh
    Replies
    3
    Views
    146

    Thanks for your reply, I hope that stuff comes in...

    Thanks for your reply, I hope that stuff comes in small quantities I do not need much. If I leave the tin alone the area will stand out like a sore thumb.
  4. Thread: Imperfections

    by 67flh
    Replies
    3
    Views
    146

    Imperfections

    This is the hood off of an old garden tractor, the tack on the brace inside gave way and I welded back in place. Each side has little divots that need to be filled. Was just gonna use lots of coats...
  5. Thread: Pressure

    by 67flh
    Replies
    15
    Views
    945

    I will be doing some practicing a lot of...

    I will be doing some practicing a lot of practicing before I actually shoot my tractor. I have lots of color on hand and a big trailer with lots of flat surface to learn on. I will work with it till...
  6. Thread: Pressure

    by 67flh
    Replies
    15
    Views
    945

    Trying to locate answer as to what type of enamel...

    Trying to locate answer as to what type of enamel it is. As far as using the same brand of hardener goes I am on 4 different message boards regarding garden tractors and all one would ever need to...
  7. Thread: Pressure

    by 67flh
    Replies
    15
    Views
    945

    Shop-line JP37x Epoxy primer Case IH Iron...

    Shop-line JP37x Epoxy primer Case IH Iron Gard Enamel made by Valspar with Shop-line JH6002/PT hardener
  8. Thread: Pressure

    by 67flh
    Replies
    15
    Views
    945

    Yes am using a HVLP gun and for the first time....

    Yes am using a HVLP gun and for the first time. Great replies! It has been 20 years since I painted with a siphon gun so I am looking forward to this. I have a small utility trailer that is going to...
  9. Thread: Pressure

    by 67flh
    Replies
    15
    Views
    945

    So I should take that set the little regulator...

    So I should take that set the little regulator that is attached to the gun, by pulling the trigger half open and adjust the pressure accordingly? Then test it with paint to see how it is?
  10. Thread: Pressure

    by 67flh
    Replies
    15
    Views
    945

    Pressure

    Air pressure questions. The manual for my gun says 2.5-3.5 bar which equals 36-50#'s Is that the rated pressure to the gun or for the gun? The primer info states 8-10 psi at the cap and 29-40 psi at...
  11. Replies
    6
    Views
    801

    Did not rec. invoice yet, my email ...

    Did not rec. invoice yet, my email iowashovel@sharontc.net Thanks!
  12. Replies
    6
    Views
    801

    I am pulling the trigger on a supplied air system...

    I am pulling the trigger on a supplied air system you only have one body and mine has got quite a few miles on it. It amazes me how many folks use hardeners in their paint with the attitude just be...
  13. Replies
    6
    Views
    801

    Thanks for your reply! When you say greatly...

    Thanks for your reply! When you say greatly reduces can you be more specific? The tractor will spend the bulk of its time out of the weather. As stated I painted tractors in the past and never used a...
  14. Replies
    6
    Views
    801

    Respirators in general

    I am strictly a hobbyist but in the past 40 years I have sandblasted using silica sand and have cleaned petroleum tanks (big tanks) while wearing Scott breathing air supplied full face masks. So I am...
  15. Thread: Blown away!

    by 67flh
    Replies
    4
    Views
    505

    Now I truly am blown away, I guess it's all...

    Now I truly am blown away, I guess it's all relative and I am glad I will only be painting a Garden tractor.
  16. Thread: Blown away!

    by 67flh
    Replies
    4
    Views
    505

    Blown away!

    Just got registered for the forum and am totally blown away by all the information here. I ended up here while doing some research on paint, hardeners and reducers. It has been 20 years since I last...
Results 1 to 16 of 16