What would be the best way to buff a small part?

[ric's62]

I have a small dash mounted clock that i painted with a s.s. poly, standing up on it's end. Ended up with a fat edge where the paint sagged. After sanding with 1500, what would be the best way to buff this out. It's about 2" dia. and 3" long. Only machines i have are a 4" Bosch and 6" Metabo elec. random orbit woodworking sanders. Thanks, Rick

[Len]

I have a small dash mounted clock that i painted with a s.s. poly, standing up on it's end. Ended up with a fat edge where the paint sagged. After sanding with 1500, what would be the best way to buff this out. It's about 2" dia. and 3" long. Only machines i have are a 4" Bosch and 6" Metabo elec. random orbit woodworking sanders. Thanks, Rick

Random orbitals are ok for removing swirls after buffing but not for removing sanding scratches. In order to remove scratches you need a rotary because a RO takes much too long to accomplish anything. We would use our 3" polisher with a foam pad after clamping the piece to the work bench or placing it in a vice to hold it while we buff. We would use Sure Finish Polish but any good quality polish could do the job.

3" Polisher Link


3" Polishing Pad Link

[Henry]

I have a small dash mounted clock that i painted with a s.s. poly, standing up on it's end. Ended up with a fat edge where the paint sagged. After sanding with 1500, what would be the best way to buff this out. It's about 2" dia. and 3" long. Only machines i have are a 4" Bosch and 6" Metabo elec. random orbit woodworking sanders. Thanks, Rick

I would prefer Len's way because that's a nice tool to have.

However, if you're brave with great control, you could mount a buffing pad in a 6 inch bench grinder and GINGERLY but the clock. Let us know what you do. Henry

[tomsteve]

i use my drill press and various set ups i made for buffing/polishing various items.

[MARTINSR]

Moving it up to 3000 grit would help you a lot too. Even by hand then just a touch of the buffer and it's shiny. Of course the best way to handle it is to simply put another coat of paint on it being more careful not to have any flaws. A slight texture is usually acceptable and a small item like that will often have next to no texture at all.

Brian

[Len]

i use my drill press and various set ups i made for buffing/polishing various items.

You reminded me of a tool that we sell that is a lot less expensive than the pneumatic polisher that I posted above. We sell a lot of these 3" hook and loop backing plate/stems that you can use with your hand drill and the 3" pads posted above.

LINK

[another2centsworth]

Small part.....after the run is sanded out with no cut throughs scuff the rest and repaint. Like Brian said. Or you can practice buffing and if you mess it up you can sand, reseal, reblock, and paint. Your choice. Small parts usually paint easier with less flaws and texture.

[tomsteve]

You reminded me of a tool that we sell that is a lot less expensive than the pneumatic polisher that I posted above. We sell a lot of these 3" hook and loop backing plate/stems that you can use with your hand drill and the 3" pads posted above.

LINK

yup. thats one of em. got it in a headlight restoration kit that was given to me and i never used it for headlights, but it comes in handy on the drill press.

[another2centsworth]

yup. thats one of em. got it in a headlight restoration kit that was given to me and i never used it for headlights, but it comes in handy on the drill press.

That is a nifty looking little pad. 8)

[Mooch]

I have a small dash mounted clock that i painted with a s.s. poly, standing up on it's end. Ended up with a fat edge where the paint sagged. After sanding with 1500, what would be the best way to buff this out. It's about 2" dia. and 3" long. Only machines i have are a 4" Bosch and 6" Metabo elec. random orbit woodworking sanders. Thanks, Rick

Could you post a picture Rick ?

Mooch