TheCoatingStore.com

Search:

Type: Posts; User: 89Blaze

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: 2K epoxy test

    by 89Blaze
    Replies
    3
    Views
    217

    Ok, thanks for the info Len.

    Ok, thanks for the info Len.
  2. Thread: 2K epoxy test

    by 89Blaze
    Replies
    3
    Views
    217

    2K epoxy test

    I have some 2k epoxy from Matrix, the activator was opened maybe 2 years ago. I mixed up a bit in a cup and let it sit for 2-3 days. It hardened up, could one assume it's ok to use? Thanks!
  3. Thread: Rotisserie

    by 89Blaze
    Replies
    1
    Views
    301

    Thanks for the pic.

    Thanks for the pic.
  4. Replies
    6
    Views
    505

    Hey Len, came across this, pretty much what you...

    Hey Len, came across this, pretty much what you were suggesting. They used 2- 2x4 square tubing.
  5. Replies
    6
    Views
    505

    Sounds good! Thanks for the info Len.

    Sounds good! Thanks for the info Len.
  6. Replies
    6
    Views
    505

    Hey Len So with the X bracing it should be fine...

    Hey Len
    So with the X bracing it should be fine to do the panel replacement on the rotisserie? It would definitely be easier to do the rockers and what not on the rotisserie. The rotisserie I'm...
  7. Replies
    6
    Views
    505

    Auto rotisserie question

    I plan on getting the body of my Suburban media blasted. I'm putting it on an auto rotisserie so they can get the undercarriage of the body as well. I've been reading that the body flexes a lot on a...
  8. Thread: Butt Welding

    by 89Blaze
    Replies
    16
    Views
    1,815

    I'm argon/co2 on my Lincoln 175-t, from my...

    I'm argon/co2 on my Lincoln 175-t, from my reading last night, and Len's input, I'm going to switch to 25 ga wire and setup some test panels and dial in my process. Thanks for the info guys!
  9. Thread: Butt Welding

    by 89Blaze
    Replies
    16
    Views
    1,815

    Haha! What wire size you guys using? I've got...

    Haha!
    What wire size you guys using? I've got .030, some are saying to use a smaller wire, like .025. And gap or no gap, the majority say put a gap in your butt weld the size of your wire....
  10. Thread: Butt Welding

    by 89Blaze
    Replies
    16
    Views
    1,815

    Butt Welding

    When butt welding, do you get a 100% tight seam? That is to say zero pin holes. Welding in a 12x12 floor panel, I'm spot welding it, jumping around as not to warp, then knocking down the welds a bit....
  11. Thread: media blasting

    by 89Blaze
    Replies
    2
    Views
    601

    Thats what I ended up doing, found a guy in...

    Thats what I ended up doing, found a guy in Union, $1500 for a Suburban.
  12. Thread: media blasting

    by 89Blaze
    Replies
    2
    Views
    601

    media blasting

    Anyone know of a media blasting company in NJ or tri-state area that does blasting and would coat the body to? I would like to have it blasted and coated, not worry about dealing with any surface...
  13. Replies
    22
    Views
    12,757

    So I went and looked at this truck today, it has...

    So I went and looked at this truck today, it has a solid body, good rockers and other parts they don't make for the Suburban. My question is about removing panels off a donor vic, do you approach it...
  14. Replies
    22
    Views
    12,757

    Got all the rusted metal out, part of the...

    Got all the rusted metal out, part of the floor,inner rocker,kick panel and outer rocker. Like a dope, I pulled the truck in and started tearing it apart. Right after I cut the kick panel out, I...
  15. Replies
    22
    Views
    12,757

    Ok, thanks Len.

    Ok, thanks Len.
  16. Replies
    22
    Views
    12,757

    Do you coat the inside of the rocker with...

    Do you coat the inside of the rocker with anything before installing it? I was thinking of scuffing up the ecoat and putting a layer of Zero Rust. Then after it's painted 3m cavity wax.
  17. Replies
    22
    Views
    12,757

    Thanks Len, I was looking closer and realized the...

    Thanks Len, I was looking closer and realized the panel I need was the kick panel. After a little bit of searching, Auto Metal Direct has them, ordered it up.
  18. Replies
    22
    Views
    12,757

    So as I was removing more of the outter rocker,...

    So as I was removing more of the outter rocker, came across something I wasn't expecting. The inner panel of the A pillar comes down and out, sitting on the floor and inner rocker( blue arrows). Part...
  19. Replies
    22
    Views
    12,757

    What rust converter do you use to take care of...

    What rust converter do you use to take care of surface rust on inner panels, like surface rust in the A or B pillar cavities. Picklex? Thanks
  20. Replies
    22
    Views
    12,757

    Yes I have them, just cutting out the main...

    Yes I have them, just cutting out the main cancer, then trying to be as surgical as possible.
  21. Replies
    22
    Views
    12,757

    Nothing big, just started to cut some stuff out....

    Nothing big, just started to cut some stuff out. Definitely have some questions coming up.
  22. Replies
    22
    Views
    12,757

    Thanks Kevin, your truck came out amazing. I...

    Thanks Kevin, your truck came out amazing. I pulled the trigger on the Plus gun a couple of times, for the price it's an awesome gun.
  23. Replies
    22
    Views
    12,757

    Thanks for the link, please I'll take all...

    Thanks for the link, please I'll take all criticism I can, it will make for a better end to my project. I was just joking with you, I have a pretty good sense of humor, nothing you said was taken...
  24. Replies
    22
    Views
    12,757

    Henry Yes it will be, this is not my first big...

    Henry

    Yes it will be, this is not my first big project, I've had many types of vehicles, in many different stages of repair. Be it gutting and redoing interiors, powertrain or suspension. But this...
  25. Replies
    22
    Views
    12,757

    Got all the parts in to start the right side...

    Got all the parts in to start the right side repairs. Have the inner/outer rocker panels, rear cab support and the floor pan. Might start it this weekend.
  26. Replies
    22
    Views
    12,757

    Got the fender and door off. Need to remove the...

    Got the fender and door off. Need to remove the rear pass door.
  27. Replies
    22
    Views
    12,757

    1986 GMC Suburban 2500 Restoration

    Starting the body work on the family Suburban. We've had the truck from day one, and she's been up and down the whole East coast a few times, and been through six new drivers. Being a Northern truck,...
  28. Replies
    5
    Views
    1,626

    Thanks for the info guys, I didn't think I had to...

    Thanks for the info guys, I didn't think I had to support the body, thanks for the heads up Henry. All the panels will be here on Tuesday, so I'll will be starting soon.
  29. Replies
    5
    Views
    1,626

    86 GMC Suburban

    Has anyone ever done full rockers on a 73-91 Burban? I've seen some good vids on Youtube, but they were all on pickups. Haven't been able to find anything, so I thought I'd ask here. Thanks21223
  30. For a longer and higher level of protection, you...

    For a longer and higher level of protection, you could use Optimum Gloss-Coat or something like it. They fall in the clear nano coating systems. I've used a few, and was very happy with the results....
  31. Replies
    5
    Views
    1,067

    Don't tell me that! Lol. It's just starting on...

    Don't tell me that! Lol. It's just starting on the driver door and rear quarter. Really don't have the time or $$$ to start anything major. But definitely don't want it to continue. The car will be...
  32. Replies
    5
    Views
    1,067

    Clear coat breaking down

    94 Camaro clear is breaking down. Looking to do a temp fix to get it through the next few years. Plan to sand off clear to base coat, respray and clear. What grit should I cut the clear with? 600....
  33. Replies
    2
    Views
    910

    Ok, thanks for the info Len. Will be placing an...

    Ok, thanks for the info Len. Will be placing an order shortly.
  34. Replies
    2
    Views
    910

    Hobbyair respirator hood

    I will be getting the Hobbyair 1 with the direct feed hood. In my research I have found some people saying they could smell paint with the hood. I'm going with the hood because of my large beard and...
  35. Replies
    8
    Views
    2,427

    Thanks for the info. I really want to use an...

    Thanks for the info. I really want to use an epoxy. I think the other brand he had was northstar epoxy primer, with a price of $350 for a gallon. The Matrix was $200, might just have to bite the...
  36. Replies
    8
    Views
    2,427

    Direct to metal Primer

    My jobber can't get the epoxy primer I want, and the other brand he has in too expensive. He has a DTM primer Matrix MP-200. I've used Matrix before and like, but never really heard of DTM. Is it...
  37. Replies
    13
    Views
    4,897

    The best way to sharpen a bit. Drill Dr, by hand,...

    The best way to sharpen a bit. Drill Dr, by hand, bench grinder. How do you guys do it? Lets see pics, dull bit.Sharpen it, and see the results.
  38. Replies
    7
    Views
    4,237

    Thanks for the heads up. Unfortunately we never...

    Thanks for the heads up. Unfortunately we never got the space, I think we scared the owner with all are legal talk. Which is a real set back! It was a amazing deal and we have yet to find anything...
  39. Thread: Rupes tool

    by 89Blaze
    Replies
    8
    Views
    2,605

    I'll leave the traditional polisher vs Rupes...

    I'll leave the traditional polisher vs Rupes alone, and give you just my opinion on the Rupes. It is a extremely well balanced machine. One handed operation, if need be, is a walk in the park. You...
  40. Replies
    29
    Views
    15,180

    I've been following this, awesome job, looks...

    I've been following this, awesome job, looks great!!
  41. Replies
    31
    Views
    6,898

    Ok sounds good. Any info or heard of this?^^^^

    Ok sounds good. Any info or heard of this?^^^^
  42. Replies
    31
    Views
    6,898

    The cowl is going to be painted one color and the...

    The cowl is going to be painted one color and the flat part of the hood another. Thinking the cowl will be blue and the flat section will be black. Plan is to shoot the black in SS, tape off, then...
  43. Replies
    31
    Views
    6,898

    Ok thanks, hope to have it painted by the end of...

    Ok thanks, hope to have it painted by the end of this week.
  44. Replies
    31
    Views
    6,898

    Hey Len I already have the Poly-flex down and...

    Hey Len

    I already have the Poly-flex down and feathered out nicely. I have 80 grit and some pin holes to cover. I bought USC Auto body Icing to put over the whole cowl and where I feathered it...
  45. Replies
    31
    Views
    6,898

    Back at it! At the point that I'm going to use a...

    Back at it! At the point that I'm going to use a polyester finishing putty as my final coat to fill some pin holes and 80 grit sanding marks. Is the polyester finishing putty flexible enough that i...
  46. Replies
    1
    Views
    560

    Replacement sheet metal

    I have a lot of metal to replace on a 86 Suburban. Anyone recommend a good place to get replacement metal? It needs rockers, inner rockers, driver/pass floors and rear quarter panels. Thanks
  47. Replies
    7
    Views
    4,237

    So true! Well after calling the state again!...

    So true!
    Well after calling the state again! And dealing with a nasty secretary, I said the hell with them and started calling local. Two calls and had all my question answered. The wastewater...
  48. Replies
    7
    Views
    4,237

    Sorry, should have specified, we are opening a...

    Sorry, should have specified, we are opening a shop and the land owner is worryed about the EPA, so I'm trying to nail down what the New Jersey Pollutant Discharge Elimination System (NJPDES) should...
  49. Replies
    7
    Views
    4,237

    NJ EPA wastewater rules?

    Anybody have any insight as to what Nj epa rules are with wastewater water from auto detailing? It will be discharged into a sewer drain not a storm drain, so right off the bat I need an oil...
  50. Replies
    9
    Views
    13,435

    I forgot I had this on here, I have to get it...

    I forgot I had this on here, I have to get it ready for August, going to the beach for a week. It needs a new front rim/tire/tube. On the ‘‘hardcore'' bike forums they definitely would disagree with...
Results 1 to 50 of 100
Page 1 of 2 1 2