TheCoatingStore.com

Search:

Type: Posts; User: Mrwelbilt

Search: Search took 0.12 seconds.

  1. Replies
    3
    Views
    514

    Greetings, Recycle ,Reuse .....GREAT idea. well...

    Greetings, Recycle ,Reuse .....GREAT idea. well done
  2. Replies
    3
    Views
    834

    So Len , Are we to assume this expansion is in...

    So Len , Are we to assume this expansion is in Spain...or USA . Personally I see no loyalty from SAGOLA regarding the North American . IN the past 15 years they have changed EXCLUSIVE importers...
  3. Replies
    13
    Views
    1,323

    The special guns that I have seen lately are...

    The special guns that I have seen lately are either STATGUN which I believe is imported from the UK . and NRD from New York are the ones that I have noticed lately. SATA also has a very complex unit...
  4. Replies
    13
    Views
    1,323

    Greeting Everyone, Humidity is often induced or...

    Greeting Everyone, Humidity is often induced or controlled to Approx. 64% ideally at OE manufacturing plants. This does vary slightly depending on the specific manufacture...the reason for the 64%...
  5. Greetings, I have have had similar situation on...

    Greetings, I have have had similar situation on cycle frames ...I learned to keep another spray gun with just urethane blending reducer and spray as needed to melt in any overspray .. by the way is...
  6. Replies
    4
    Views
    1,021

    I have yet to find any OE manufactures to...

    I have yet to find any OE manufactures to recommend copper based only zinc for welding primer
  7. Replies
    8
    Views
    1,053

    Greetings 80 GRIT, I learned how to spread large...

    Greetings 80 GRIT, I learned how to spread large areas of filler from terry at EXACTLINE TOOLS . one of the secrets is to find compatable body filler and polyester glaze that can be blended together...
  8. Thread: paint room

    by Mrwelbilt
    Replies
    5
    Views
    818

    Greetings , during the 60's and 70's both BINKS ...

    Greetings , during the 60's and 70's both BINKS and DEVILLBIS offered positive pressure cross flow designs .... the front doors which contained the intake filters had an additional intake shroud...
  9. Replies
    7
    Views
    801

    Greetings , you may prepare yourself for a...

    Greetings , you may prepare yourself for a little bit of the run -a-round from the insurance company since '' WE JUST PAY THE BILL AND SETTLE THE CLAIM ...THE SHOP SHOULD WARRANTY ThE REPAIR '' ...
  10. Replies
    5
    Views
    1,300

    Greetings , you may wish to fit the doors and...

    Greetings , you may wish to fit the doors and front fender back on just to confirm that you have the desired body lines and gaps BEFORE welding the replacement rocker in place, Best regards Mike
  11. Replies
    19
    Views
    3,472

    Greetings , Sagola offers a very nice case with...

    Greetings , Sagola offers a very nice case with capacity for 3 guns and a variety of air caps ... many companies refer to it as a salesmans case , I also have similar cases from JAFE SPRAYGUNS and...
  12. Replies
    17
    Views
    4,668

    Greetings, not much to report back with...nothing...

    Greetings, not much to report back with...nothing on display or possibly hear run. they are having a scratch and dent sale on welders NOV. 11 they expect to have one on display by then
  13. Replies
    17
    Views
    4,668

    Greetings, I will be heading down to Eastwood on...

    Greetings, I will be heading down to Eastwood on Thursday for supplies, i will ask the boys if they have one setup on display and to get a look at it for you. there is huge possibility that these are...
  14. Replies
    14
    Views
    1,524

    Greetings Guys, when i stated the best days of...

    Greetings Guys, when i stated the best days of this industry are behind us , I am referring to the body repair and collision industry ....not the manufactures. why has every manufacture gone a...
  15. Replies
    14
    Views
    1,524

    Greetings Martinsr, I agree with many areas of...

    Greetings Martinsr, I agree with many areas of your observation. all the crash testing info that i have found is based on a 80 mph impact ( 40 MPH times 2 ) from what i have read the speeds were 70...
  16. Replies
    14
    Views
    1,524

    Greetings Henry and Len , I believe from what...

    Greetings Henry and Len , I believe from what info i have been able to gather and have talked to someone who was present for the trial, the jury focused on the fact that Honda could show how the...
  17. Replies
    14
    Views
    1,524

    Greetings Len, I do agree with you on what we...

    Greetings Len, I do agree with you on what we have been told , But never the less if you do not follow the direct OE repair procedures you are now assuming the liability . apparently Honda does not...
  18. Replies
    4
    Views
    1,578

    Greetings , I agree with observation that the...

    Greetings , I agree with observation that the damage was most likely caused by a portapower ram . with that being said if your access to the damage is limited due the motor being in the way , i would...
  19. Replies
    6
    Views
    1,421

    Greetings, I agree with Henry on this one... find...

    Greetings, I agree with Henry on this one... find yourself a frame data sheet for you year and model , things were pretty basic years ago and NEVER perfect , tollerances of plus or minus a 1/4 inch...
  20. Replies
    18
    Views
    16,852

    Greetings, Keep in mind that i have never seen an...

    Greetings, Keep in mind that i have never seen an expiration date on an air bag or have heard of a manufacture advise that the be replaced after so many years or miles, with that being said i have...
  21. Replies
    14
    Views
    1,524

    liability of panel bonding

    Greetings everyone, there was a recent jury verdict in Texas regarding panel bonding a roof panel of a hail damaged honda several years back. A few interesting things about this trial ...the car had...
  22. Greetings, I would repair both panels. This would...

    Greetings, I would repair both panels. This would enable the base coat blend and clear coat on the door and Q-panel avoiding the detrim and blending onto the front door. . With some of the latest...
  23. Replies
    13
    Views
    4,196

    Greetings Welddoc, you may wish to go out on...

    Greetings Welddoc, you may wish to go out on youtube and do a search on RETRACTABLE SPRAYBOOTH and CARCOON you should be able to absorb some ideas for you construction ideas , also at SEMA this year...
  24. Replies
    13
    Views
    4,196

    Greetings Welddoc, Your calculations are correct....

    Greetings Welddoc, Your calculations are correct. Where the 100 ft. comes from is OLD safety codes when crossflows were the typical booth of the 50s 60s and 70s . the codes are still standing today....
Results 1 to 24 of 24