TheCoatingStore.com

Search:

Type: Posts; User: Bob K

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Guide coat is more like stain than paint but it...

    Guide coat is more like stain than paint but it wonít sink into surfacer. It just makes a color on the surface but doesnít add thickness like paint would. Paint can plug your sandpaper when you sand...
  2. Hard to say what caused it. Maybe itís from not...

    Hard to say what caused it. Maybe itís from not using enough pressure on the spreader, maybe itís air bubbles. No matter what caused it, you still need to sand it flat. Sand it down and add more...
  3. Replies
    11
    Views
    139

    Maybe you could take the channel you made and...

    Maybe you could take the channel you made and drill some 5/16 inch holes in it like every 8 inches or so and plug weld it to the door frame after you bend it to the shape of the door. After itís...
  4. Replies
    11
    Views
    139

    As long as youíre not trying to keep the door...

    As long as youíre not trying to keep the door authentic then you donít need to use a channel at all but weld two narrow stips of sheet metal to the door frame and then with a body hammer just fold...
  5. Replies
    4
    Views
    143

    Iím sorry, I donít know any of those guns so I...

    Iím sorry, I donít know any of those guns so I have no opinion on them. I just buy a gun based on my own evaluation with the help of information from people I trust but I have never bought the best...
  6. Replies
    4
    Views
    143

    Give it a try. Base coat clear coat is very...

    Give it a try. Base coat clear coat is very forgiving and easy to fix if you donít like the results. The reason to get a big compressor and better gun is you plan to do a lot of this work. If you...
  7. Replies
    2
    Views
    178

    Itís all well and good to get the water out of...

    Itís all well and good to get the water out of your compressed air but it isnít all water. That is to say a filter will not remove water vapor. That is a gas thatís in the air thatís in the tank. The...
  8. Replies
    14
    Views
    559

    Len sells Bloxygen in the store on this site. ...

    Len sells Bloxygen in the store on this site.

    Bob K
  9. Replies
    13
    Views
    831

    You can fix the one you have but it isnít as...

    You can fix the one you have but it isnít as cheap as you may think. Body filler wonít work. The cracks will come back in a short time. You will have to open up all the cracks with a grinder and fill...
  10. Replies
    13
    Views
    831

    I feel like Iíve lost my powers of observation....

    I feel like Iíve lost my powers of observation. Your license plate shows what part of the country youíre in and I could have been a little more helpful by narrowing the search to your neighborhood...
  11. Replies
    13
    Views
    831

    I donít know where you live so I did a nationwide...

    I donít know where you live so I did a nationwide search on www.car-part.com and found a silver tire cover in South Carolina for $125 and several silver rear door assemblies for less than $200. You...
  12. The gun needs 10 PSI at the air cap as per...

    The gun needs 10 PSI at the air cap as per government regulation but you need to apply more pressure at the hose to get that. Bump the pressure up to 30 or 40 at the base if the gun with the trigger...
  13. Replies
    5
    Views
    314

    As for removing the wheel, do it whether itís...

    As for removing the wheel, do it whether itís needed or not, you will appreciate the extra room to work. You probably wonít hurt the tire but the rim is another story. Grinding sparks can do a lot of...
  14. Replies
    4
    Views
    438

    Iíve had good luck with those stains using a clay...

    Iíve had good luck with those stains using a clay bar. Itís a little labor intensive but it is safe for the paint.

    Bob K
  15. Replies
    7
    Views
    354

    I did a lot of work in the past fixing small...

    I did a lot of work in the past fixing small dings on fenders and finally realized that fenders are so cheap that I replace them now any time I can get a new one from Certifit.

    To answer your...
  16. Replies
    1
    Views
    214

    How good it looks in the end is proportional to...

    How good it looks in the end is proportional to the effort you put into preping it. I donít know how aggressive your DA is and what grit you used but there are probably variations in the level in old...
  17. Replies
    16
    Views
    1,791

    Remember, itís just sheet metal. A hammer makes...

    Remember, itís just sheet metal. A hammer makes it go anywhere he wants it. After all the guy is fixing a series of dents. Whatís one more dent?

    Bob K
  18. I just looked at my CertiFit catalog and it looks...

    I just looked at my CertiFit catalog and it looks like they have most of what you need. My experience has been that new condensers and radiators from them cost about the same as used parts. Iíve been...
  19. Replies
    5
    Views
    941

    That's an example of a place where the price...

    That's an example of a place where the price should not be a factor. Go with the best certification you can find no matter what the price. The price of failure at the worst possible moment could be...
  20. What they told me at the store is that you have...

    What they told me at the store is that you have to open the fixture up and take the balest out of the circuit and wire the LED to the 120 volt line. I havenít done it yet but may need to when the...
  21. Replies
    4
    Views
    333

    You will have a lot left over so consider what...

    You will have a lot left over so consider what size you will want to inventory and use in the future. The thin stuff is easy to make curves with and thatís what I have, about 1/8 inch. After you mark...
  22. That sounds like a good idea but itís more stuff...

    That sounds like a good idea but itís more stuff to have on the gun and it might cause a bit of a control problem along with getting a lot of overspray on the lens. Iíve got a lamp that I strap over...
  23. One more thing came to mind today as I was...

    One more thing came to mind today as I was setting my gun up for a job. I remembered you said just before the gun you had a regulator then a desiccant dryer. Was the pressure gauge on the regulator?...
  24. Do you set the air pressure to the gun with the...

    Do you set the air pressure to the gun with the trigger pulled? As I said before, increase the air pressure even above what the gun calls for. When the pressure is correct a lot of the solvent...
  25. Replies
    10
    Views
    1,421

    Did they show you a warranty document that stated...

    Did they show you a warranty document that stated the compressor needed to be outside to be covered under warranty? I think that was a made up statement to get you to go away. They already had lost...
  26. Replies
    6
    Views
    333

    3/4" pipe adds a lot of restriction due to the...

    3/4" pipe adds a lot of restriction due to the small diameter and relative low pressure in the system. 2" pipe is cheep and will restrict the air flow a lot less. I can't say anything about the out...
  27. Replies
    5
    Views
    346

    I don't think I've used sealer for 10 years or...

    I don't think I've used sealer for 10 years or more. If you use good base coat it should cover in two coats, three if you want insurance. Go for it. It's nice to know what the problem was. It never...
  28. Replies
    5
    Views
    346

    If you got it fixed tell us about it. It's nice...

    If you got it fixed tell us about it. It's nice to have both sides of the coin. We all get problems once in a while and it's nice to know how the fix went down.

    Bob K
  29. You can cause those same solvent pop craters by...

    You can cause those same solvent pop craters by reducing the pressure on your gun. You get a good looking clear coat application but the craters will show up in time. Try adding 10 PSI over your...
  30. Replies
    10
    Views
    1,115

    If you could run 2 ea 10í lines horizontally you...

    If you could run 2 ea 10í lines horizontally you could do without the drain taps on each leg. Run a line straight to the wall from your compressor and turn the line 90 degrees with the fitting...
  31. Replies
    17
    Views
    853

    Donít think of it as wasted product, think of it...

    Donít think of it as wasted product, think of it as better outcome.

    Bob K
  32. Replies
    17
    Views
    853

    Did you set the gun pressure with the trigger...

    Did you set the gun pressure with the trigger pulled as you should? Did you use the recommended pressure for that product as per the gun manufacturers recommendations? Iíve done some tests to see how...
  33. Replies
    8
    Views
    503

    I donít think there is anything wrong with your...

    I donít think there is anything wrong with your primer surfacer but the epoxy doesnít look like it cured. Was it warm enough to spray the epoxy? Was the correct hardener used? Were both epoxy...
  34. Replies
    5
    Views
    723

    Yes, air bag module, and no not the front bumper...

    Yes, air bag module, and no not the front bumper but just the cover so you can see the collision sensors and the wires that go into the loom. You donít have to open the entire loom but follow it to...
  35. Replies
    5
    Views
    723

    Are you up to working on this yourself? It can...

    Are you up to working on this yourself? It can be tricky to get things right. You need to be aware of all the components on your car and be able to check all of the wiring, find all the sensors and...
  36. Replies
    4
    Views
    439

    I would be inclined to wash it with Dawn with a...

    I would be inclined to wash it with Dawn with a good scrub brush. When dry I would go over it with wax and grease remover then scuff it with 800 grit and paint it. If it's chipped I would feather the...
  37. Replies
    4
    Views
    534

    Set the wall regulator to something like 80 psi,...

    Set the wall regulator to something like 80 psi, then set the pressure at the gun to the pressure called for by the gun manufacturer while the trigger is fully pulled. If you change the fan pattern...
  38. I said that to reduce the chances of cutting the...

    I said that to reduce the chances of cutting the paint off the sharp edges. 1200 cut slowly but you only have the tops of the nibs to remove so being careful you should be able to get a paintable...
  39. Try a quarter sheet of 1200 grit. Fold it in...

    Try a quarter sheet of 1200 grit. Fold it in thirds and use your index finger for backing. Use it wet to keep it from plugging and be careful. When it no longer sands turn it over and sand with the...
  40. Thread: Paint guns

    by Bob K
    Replies
    37
    Views
    3,700

    I wouldn't set a cutoff price but I can say I...

    I wouldn't set a cutoff price but I can say I have an FLG 3 with a 1.3, 1.8 and a 2.2 tip that I used as my primary gun for many years. The FLG 4 is a newer improved model. I got a more expensive gun...
  41. Thread: Advice needed

    by Bob K
    Replies
    6
    Views
    606

    If the car was totaled for hurricane damage, then...

    If the car was totaled for hurricane damage, then it wasn't for that dent, it was for flooding and the flood damage usually causes electrical problem after corrosion builds in many of the electrical...
  42. Replies
    20
    Views
    1,850

    You ask if spraying with Slick Sand is necessary....

    You ask if spraying with Slick Sand is necessary. The way I look at it is, I spray Slick Sand "IF" it's necessary and I don't do it very often. To be truthful I spray Feather Fill G2 instead. That's...
  43. Replies
    7
    Views
    835

    Filler is pours so it absorbs the primer. I...

    Filler is pours so it absorbs the primer. I always put 2k surfacer on top of filler and wet sand it. If there is a lot of metal showing I put the epoxy on the metal and don't try to prevent it from...
  44. Just a couple random thoughts as I have done some...

    Just a couple random thoughts as I have done some of this kind of work the same way. As for using the fork lifts as dead weight I've found you can drag them around with surprisingly small effort. I...
  45. 80 grit scratch on metal is much shallower than...

    80 grit scratch on metal is much shallower than 80 grit scratch on filler because the filler is so much softer. The deeper scratch on filler leaves the next coat thicker in the scratch channel. When...
  46. Replies
    8
    Views
    807

    It's not the history of the box that's important...

    It's not the history of the box that's important here, it's the future use that demands maximum bond.

    Bob K
  47. In place of the poly I would use 2k urethane...

    In place of the poly I would use 2k urethane surfacer and wet sand it with guide coat unless there is damage on the metal that needs a thin coat of filler. After I spray poly on I still use surfacer...
  48. Thread: Clearcoat issue

    by Bob K
    Replies
    13
    Views
    1,375

    Keep in mind that you may be putting each coat on...

    Keep in mind that you may be putting each coat on to thick. This happens when you spray with the pressure to the gun to low. The clear goes on without loosing enough of the solvent into the air. I...
  49. Replies
    19
    Views
    2,497

    I found quite a few fuse boxes in NJ for $75 to...

    I found quite a few fuse boxes in NJ for $75 to $135 on www.car-part.com You can enter your car in the search box, select the part and search by distance to find the parts near you and the price for...
  50. Replies
    4
    Views
    790

    A pint of black base coat goes a long way and if...

    A pint of black base coat goes a long way and if I use the code it matches up quite well. I've never seen multiple variants for a black car, but on the other hand I haven't painted many black ones. I...
Results 1 to 50 of 100
Page 1 of 2 1 2