TheCoatingStore.com

Search:

Type: Posts; User: Len

Page 1 of 2 1 2

Search: Search took 0.15 seconds.

  1. Replies
    39
    Views
    701

    If its been sanded with 400 or more coarse you...

    If its been sanded with 400 or more coarse you should be ok just to shoot it.
  2. Replies
    39
    Views
    701

    The problem with putty is that it's almost...

    The problem with putty is that it's almost impossible to apply it to a large are evenly. I'd recommend spraying on a filler primer like Slick Sand or some other heavier primer then guide coat again...
  3. Replies
    9
    Views
    92

    You can help the weaker strippers by applying it...

    You can help the weaker strippers by applying it then covering it with plastic film for an hour or two then remove the film and scrape off the paint. The film helps drive the stripper down into the...
  4. Replies
    6
    Views
    73

    If that's the case I would probably do what I...

    If that's the case I would probably do what I suggested then coat it with some gravel guard.

    ...
  5. Replies
    6
    Views
    73

    Scuff it with some 80 grit paper and apply...

    Scuff it with some 80 grit paper and apply Picklex 20, work it in with a scuff pad then wipe it off and allow it to dry. Once it's dry apply a couple of coats of Zero Rust.

    ...
  6. Thread: Filling large gaps

    by Len
    Replies
    2
    Views
    51

    All Metal would probably work but I usually use a...

    All Metal would probably work but I usually use a short strand fiberglass filler in situations like that for the initial filling then finish the job with a regular polyester filler.

    ...
  7. Clean it well that spray it with epoxy primer.

    Clean it well that spray it with epoxy primer.
  8. Replies
    39
    Views
    701

    What type of paint will you be using? Single...

    What type of paint will you be using? Single stage or base clear and what color?
  9. Thread: Paint chip repair

    by Len
    Replies
    6
    Views
    152

    Good Luck, let us know the direction you take and...

    Good Luck, let us know the direction you take and the outcome.
  10. Replies
    39
    Views
    701

    2K primer is usually applied to help level any...

    2K primer is usually applied to help level any variables and fill scratches, it's fine to cover the entire surface with it but it's not usually necessary. Be sure to spray a guide coat lightly over...
  11. Replies
    5
    Views
    99

    Steck makes a door rest that may work for you but...

    Steck makes a door rest that may work for you but you would need a floor jack to attach it to. This stand would cost you $121 plus shipping.

    ...
  12. Replies
    5
    Views
    99

    Do you need it anchored so that you can pull and...

    Do you need it anchored so that you can pull and push on it?
  13. Replies
    39
    Views
    701

    Are you spraying all those part entirely with...

    Are you spraying all those part entirely with high build? That's a lot of block sanding.
  14. Thread: Paint chip repair

    by Len
    Replies
    6
    Views
    152

    Especially when the paint is a solid...

    Especially when the paint is a solid (non-metallic) color you can make the chip disappear.
  15. Thread: Paint chip repair

    by Len
    Replies
    6
    Views
    152

    Paint chip repair LINK...

    Paint chip repair LINK
  16. It depends on the characteristics of the primer,...

    It depends on the characteristics of the primer, if it sands without filling the pad too quickly then it can be used for a longer time. But if the primer is gummy or harder it can clog or wear on...
  17. Thread: CarParts.com Tip

    by Len
    Replies
    1
    Views
    114

    CarParts.com Tip

    We just placed our third order with CarParts.com, the first two were plastic bumper covers that arrived damaged so we repaired them the third is a Mercedes headlamp assembly that was never delivered...
  18. Replies
    39
    Views
    701

    We use several methods for removing paint. For...

    We use several methods for removing paint. For most of the exterior we just use 80 grit disks on a variable speed buffer but on areas that are hard to get to we either use chemical stripper or a...
Results 1 to 18 of 100
Page 1 of 2 1 2