TheCoatingStore.com

Search:

Type: Posts; User: Len

Page 1 of 2 1 2

Search: Search took 0.27 seconds.

  1. Replies
    2
    Views
    16

    I've never tried to repair damaged paint using...

    I've never tried to repair damaged paint using aerosols but it may be difficult to get a good match. We would sand out the cracks and apply a flexible filler primer then block sand to level the...
  2. Thread: Paint Booth Build

    by Len
    Replies
    11
    Views
    75

    Yes, that's my only exhaust and the room clears...

    Yes, that's my only exhaust and the room clears in about two minutes.

    Because it's positive pressure when I leave or enter the booth the air blows out so no dust enters the room.
  3. Thread: Paint Booth Build

    by Len
    Replies
    11
    Views
    75

    Yes that can work it's just about the type/size...

    Yes that can work it's just about the type/size of the fan and how much air (CFM) it can move against the pressure in the room. Also the incoming air should be filtered well or you could generate...
  4. Thread: Paint Booth Build

    by Len
    Replies
    11
    Views
    75

    That's where it goes.

    That's where it goes.
  5. Thread: Paint Booth Build

    by Len
    Replies
    11
    Views
    75

    I cut a 4' X 2' hinged panel at the bottom of my...

    I cut a 4' X 2' hinged panel at the bottom of my over head that I open when painting. I put in a screen/filter that removes most of the overspray.
  6. Thread: Paint Booth Build

    by Len
    Replies
    11
    Views
    75

    Positive pressure is normally more complicated to...

    Positive pressure is normally more complicated to install but is usually the better choice. Negative pressure can usually be achieved by just putting a fan in a window and filtering the incoming air...
  7. Thread: ONLY ONE AVAILABLE

    by Len
    Replies
    0
    Views
    66

    ONLY ONE AVAILABLE

    I just got word from our Sagola Warehouse that they have one Sagola Mini Xtreme overstocked and want to sell it NOW. This is one of my favorite goto guns for spraying smaller jobs like motorcycles...
  8. A lot of guys hang masking plastic on walls and...

    A lot of guys hang masking plastic on walls and ceiling and replace it when it gets dirty. It's less expensive and can be used to protect other surfaces.
    ...
  9. Thread: Devilbiss Mini gun

    by Len
    Replies
    5
    Views
    91

    Yes the needle for the 1.2 is different so you...

    Yes the needle for the 1.2 is different so you would need to purchase it also.
  10. Replies
    5
    Views
    60

    We normally use tape but after the filler is...

    We normally use tape but after the filler is applied and still soft we remove the tape. In most cases we don't leave the tape on until the filler gets hard.
  11. Thread: sande paper grid

    by Len
    Replies
    2
    Views
    58

    We normally end up sanding our filler with 220...

    We normally end up sanding our filler with 220 then apply primer then block wet sand the primer with 400 or 600 grit before painting. We guide coat everything and judge the primer sanding grit by...
  12. Thread: De Beer Paint

    by Len
    Replies
    1
    Views
    38

    Try this one.... LINK...

    Try this one.... LINK
  13. We use dry guide coat on body filler and aerosol...

    We use dry guide coat on body filler and aerosol guide coat when wet sanding but the aerosol can also be used on body filler, I just don't like using it multiple times in a confined area then...
  14. Replies
    19
    Views
    259

    Yep that sounds like a pretty good deal...

    Yep that sounds like a pretty good deal especially if you can control the air flow and temperature.
  15. Replies
    19
    Views
    259

    I built my own booth that can be seen HERE...

    I built my own booth that can be seen HERE but I've got to clean it well before I spray. In my old shop many years ago I purchased a booth but it wasn't a down draft, if I were to do it again I...
  16. Replies
    9
    Views
    99

    Is that Medford Speed in Vincentown NJ ?

    Is that Medford Speed in Vincentown NJ ?
  17. Thread: Devilbiss Mini gun

    by Len
    Replies
    5
    Views
    91

    The 1.2 will allow more paint to come from the...

    The 1.2 will allow more paint to come from the gun but will use about the same amount of air. It's an air cap that has more effect on the air but I don't think there are any other air cap options...
  18. Thread: Devilbiss Mini gun

    by Len
    Replies
    5
    Views
    91

    No that's a good gun for most standard finishes. ...

    No that's a good gun for most standard finishes. The full size guns take larger tips like 1.3 or 1.4 but the detail guns like the SRI Pro use smaller tips like a .8, 1.0 or 1.2.

    The only thing...
  19. Replies
    1
    Views
    65

    Me or my friends have used all of those guns and...

    Me or my friends have used all of those guns and I'd recommend the Sagola 4600 over all of them. The 4600 comes with two air caps, HVLP and other cap of your choice, I'd recommend the clear cap. ...
  20. Replies
    0
    Views
    56

    Free Holiday Shipping

    We will be shipping Sagola 4600 Spray Guns and Hobbyair Breathing Systems FREE to 48 States until 12/24/19.

    This can save from $15 to $25 on the Sagola 4600 and $25 to $60 on Hobbyair Systems.

    ...
  21. The number of clear coats depends on how well the...

    The number of clear coats depends on how well the gun and clear cover the surface. I'd probably say two coats should do it.

    Time before taping on the clear depends on the temperature, the...
  22. Right! It's probably part of certain programs, I...

    Right! It's probably part of certain programs, I haven't found it here.
  23. Apply more Apply more pressure on the first pass...

    Apply more Apply more pressure on the first pass so that the filler gets pressed into the scratches and bonds well with the surface. Also, after block sanding the filler you may have low areas that...
  24. We've used this graphic material but I don't know...

    We've used this graphic material but I don't know how it reacts to aluminum. It's normally cut with a plotter, stuck/positioned on the work then the area to be painted is removed and the remaining...
  25. Sorry, I still don't get it.

    Sorry, I still don't get it.
  26. Replies
    1
    Views
    63

    If you don't have a sand blaster you can sand off...

    If you don't have a sand blaster you can sand off the paint then apply something like Picklex 20, rub it in and wipe it off and allow it to dry then scuff it and prime it with epoxy primer that...
  27. Replies
    9
    Views
    99

    Cool car, I've restored a few of them myself. I...

    Cool car, I've restored a few of them myself. I don't think anyone made a quarter panel any longer than that. :steering:
  28. Hmmm, I post png images all the time, here's...

    Hmmm, I post png images all the time, here's one... 26695

    What do you mean? You should be able to mention any users you want.

    With the images be sure to "Browse" to find your image then...
  29. Yep, that looks pretty good. We will sometimes...

    Yep, that looks pretty good. We will sometimes tape a body line in order to apply the filler along that peak but we normally remove the tape before the filler hardens so that the tape isn't trapped...
Results 1 to 29 of 100
Page 1 of 2 1 2