Search:

I haven't painted in years but when I was in the tradeI used Siphon guns Binks Model 7, but I did buy a G670 plus and its a nice gun, it put's a lot of paint on, but if you practice with it as I did...

You could build a de tached garage for that, looks like the lighting would be poor.

What about PPG's Shop Line ?

If its holding on an emblem I use fising line to cut through it, then I used a wax and grease remover Ditzler DX330 didn't work as well as 3M citrus base cleaner, sprayed it on let it set a bit...

On another forum there was a discussion on moisture in the air lines the cheap fix was to run your air hose out of the compressor coil up 20 -25 ft or so into a 5 gal bucket of ice water to cool the...

Is 500 wet/sand paper too fine for preping 2 k primer for 2 k sealer, also my base is DuPont Chroma Base?

I am also sanding the OEM factory clear that requires no body work with 500 wet, seems I...

What presure do you normally have at the regulator when you want about 25-35 psi at the gun?

I don't understand what he is telling you, If you have 100 psi at the filter/regulator and adjust that to 28psi at the gun where is the difference.

...

If your compressor is working hard to keep up, the air will be hot as stated above and it has been my experience that if the hose is allowed to lay on the cool concrete floor that will contribute to...

I have the same gun what have your results looked like as far run,sags, orange peel, needing cut and buff?

thanks Tom

What about DuPont Chroma base?

Does high humidiy over 55% and above effect activated urethane universal clear and activated sealers. I would think it may effect drying time, but will it cause the clear or sealer to become cloudy....

Anyone shooting this product and what kind of coverage are you getting with this base, I am thinking of useing this in Black Sand Pearle over areas of gray primer gray primer, I was thinking of...

Posted: Sun Jun 26, 2011 9:16 am
Does Humidity effect certain colors of urethane base coat, and clear as it does lacquer?

thanks
tom

It was always my thoughts that if washed a panel with Dawn soap to remove any wax and prior to any body work or sanding you used a wax and grease remover you were good to go as far as removing any...

take a look at

http://www.southernpolyurethanes.com/

I intend to use this on my Tacoma, I have heard nothing but good comments on there products

I went the epoxy route and followed the directions to the letter and with the winter salt and gravel the paint still wears off wish I would of never messed with it.

Well isn't the compressor going to have to run twice as long to keep up with two tanks and with the high cycle rate there will be heat createing more moisture, especially if your compressor is a...

I used to heat the under side with a torch and that helped the glue to release.

I got out some info that I had from a Binks 7 in the trouble shooting area it said that dried out packing can be corrected by backing up the knurled nut and place two drops of light machine oil on...

Don't have an answer for you but can't wait to read you comments on the Plus. Pic's too if you can.

Let us know your thoughts on the gun after you finish, just curious how much prior experience do you have painting,you stated that its the first time with the Plus,wondering if you have used other...

What about the Devibliss Plus?

Keep us advised on the conversion.

Post pictures of your H/M booth.

Can't knock a free heater but I would think that the fumes from the heater woould contaminate a paint surface, I know they give you a headache.

Let us know how you like the Plus!

Do you get to keep the gun if you leave the job? How many painters in your shop?

I remember Earl and the heating up the enamel. those completes were some nasty paint jobs!