TheCoatingStore.com

Search:

Type: Posts; User: Houndogforever

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Hey Len, I'm curious how far you extend the...

    Hey Len, I'm curious how far you extend the single stage. An inch? 6"?

    I assume after the single stage is cured, you just scuff/sand the overspray off and single coat to a blend line.
  2. You need to step back a minute on this project. ...

    You need to step back a minute on this project.

    You are jumping to very complicated fixes, ie adding more putty filler and sanding it off etc.

    Have you tried just getting some polishing...
  3. Replies
    20
    Views
    1,037

    Most epoxy primers have a set time that after you...

    Most epoxy primers have a set time that after you spray it, if you spray something else on top within a time window, you don't need to scuff the surface.

    So if you have a 24 hour recoat window,...
  4. I may have (probably did) screw up.

    I was touching up the firewall on my car and there were some scratches showing thru right up at the top. I tried sanding the zero rust to smooth it and re-coat, but the scratches still showed thru....
  5. Replies
    4
    Views
    354

    32293 32294 Yeah, up where your toes are. ...

    32293

    32294

    Yeah, up where your toes are. The pad has a bunch of rubber plugs that roughly fasten it to the inside firewall. I'm just certain that getting the heater box up there without it...
  6. Replies
    4
    Views
    354

    Spray adhesive?

    In a shock to my own system, it appears I am attempting to re-assemble my project car.

    I am about to install the heater box and I have an insulation pad that goes on the inside of the car. It has...
  7. If it is a brand new hitch, take it to the powder...

    If it is a brand new hitch, take it to the powder coaters. That will protect it.
  8. Replies
    4
    Views
    373

    Cool pointer, thanks. I was originally...

    Cool pointer, thanks.

    I was originally thinking of something like optimum no rinse, or a detailing spray, but the more I thought of those the more I thought they might have silicone in them for...
  9. Replies
    4
    Views
    373

    Cleaning pre-paint

    Ok, I'm done with the undercoating and such. Now I need to wash down everything in the frame rails and engine area.

    I'm thinking just some Dawn dishwashing liquid and water to sponge things down...
  10. Replies
    7
    Views
    535

    It would have been proper to grind off the bottom...

    It would have been proper to grind off the bottom side when I cut out the old patches, however at the time 4-6 years ago, I didn't even have the front end sheet metal off much less the engine and...
  11. Replies
    7
    Views
    535

    There is a welded in patch panel behind all that...

    There is a welded in patch panel behind all that fusor. All that fusor is about 1/8 deep The inside was ground smooth and painted a couple years ago.

    There was weld bubbles, wire sticks etc...
  12. Replies
    7
    Views
    535

    OK. Here are some pics. First one is looking...

    OK. Here are some pics.
    First one is looking thru the engine compartment. You can just see some of the fusor sealant from the front.

    32147

    Here is under the driver seat. The patch was...
  13. Replies
    7
    Views
    535

    Under body painting.

    ick
    I have patched and sealed a couple patches in the floor.

    Now the bottom of the car is the bottom of a 50 year old car. It's dirty/oily.

    I rough sanded things down a bit around all the...
Results 1 to 13 of 100
Page 1 of 2 1 2