TheCoatingStore.com
Tab Content
  • JMTC's Avatar
    01-14-2019, 07:10 AM
    I feel your pain, did exactly the same thing a couple weeks ago, (minus the bugs) I just 2k primed the areas that burned through. Best of luck this...
    2 replies | 82 view(s)
  • JMTC's Avatar
    01-08-2019, 10:11 AM
    JMTC replied to a thread Small burn through clear in Final Touch
    Thanks, 1978 Gm paint code 22
    23 replies | 474 view(s)
  • JMTC's Avatar
    01-06-2019, 05:09 PM
    JMTC replied to a thread Small burn through clear in Final Touch
    I'm wet sanding the roof of car with p1000 wet and so far noticed a single deep fish eye, If I mixed up a few drops of clear and dabbed a tiny bit in...
    23 replies | 474 view(s)
  • JMTC's Avatar
    01-05-2019, 09:47 PM
    JMTC replied to a thread Small burn through clear in Final Touch
    Well I hand blocked the whole car down with 600 dry,. re-based and I am waiting to put on my third coat of clear as I sit here and type. The new gun...
    23 replies | 474 view(s)
  • JMTC's Avatar
    01-03-2019, 08:30 PM
    JMTC replied to a thread Small burn through clear in Final Touch
    I spent the time and blocked this thing super strait and I want to see that at the end, so yes I will be taking out the peel and there will be plenty...
    23 replies | 474 view(s)
  • JMTC's Avatar
    01-03-2019, 07:20 PM
    JMTC replied to a thread Small burn through clear in Final Touch
    I bought a new finish line gun and I am going to base coat the rear quarter then re clear whole tub this weekend. How many coats clear should I put...
    23 replies | 474 view(s)
  • JMTC's Avatar
    01-03-2019, 07:20 AM
    JMTC replied to a thread Small burn through clear in Final Touch
    (Just remember heat and sunlight is your friend.) I assume you mean for clear to harden up properly? Jim
    23 replies | 474 view(s)
  • JMTC's Avatar
    01-02-2019, 05:16 PM
    JMTC replied to a thread Small burn through clear in Final Touch
    It's Matrix AG-40LV autoglas Euro design 5 litres was $140 two to one. Hardener $116 Canadian plus 13%hst lol. Not quite to the good level. On a...
    23 replies | 474 view(s)
  • JMTC's Avatar
    01-02-2019, 04:36 PM
    JMTC replied to a thread Small burn through clear in Final Touch
    Ugh, I noticed a wave in the rear fender body line from a run I sanded out. I put sharpie all over it as a guide coat and wet sanded with p1200 then...
    23 replies | 474 view(s)
  • JMTC's Avatar
    01-02-2019, 10:14 AM
    JMTC replied to a thread Small burn through clear in Final Touch
    Awesome got it!! Thanks Jim
    23 replies | 474 view(s)
  • JMTC's Avatar
    01-02-2019, 08:59 AM
    JMTC replied to a thread Small burn through clear in Final Touch
    Just to clarify, over reduce with reducer? as in DO NOT use thinners? I will get a touch up gun when i go to the city tomorrow. Thanks again Jim
    23 replies | 474 view(s)
  • JMTC's Avatar
    01-02-2019, 07:33 AM
    JMTC replied to a thread Small burn through clear in Final Touch
    Thanks for the reply Len, I have had lots of issues getting this far, some have felt like quick sand, every time I try to fix something I sink in a...
    23 replies | 474 view(s)
  • JMTC's Avatar
    01-01-2019, 09:22 PM
    Hi all, great forum! been doing lots of reading for hours on here but can't find a solution to my exact problem (size and location of blemish) It's...
    23 replies | 474 view(s)
No More Results
About JMTC

Basic Information

Statistics


Total Posts
Total Posts
13
Posts Per Day
0.87
General Information
Last Activity
Today 04:53 AM
Join Date
01-01-2019
Referrals
0