TheCoatingStore.com

Tab Content
Len's Activity
About Me
Tab Content
  • Len's Avatar
    Yesterday, 08:21 AM
    Len replied to a thread Welding table in General Discussion
    Also look on Face Book Marketplace for new and used tables. Search "welding table".
    6 replies | 43 view(s)
  • Len's Avatar
    01-24-2022, 08:47 AM
    Len replied to a thread body filler in General Discussion
    I used All Metal a couple times but didn't like the way it sanded so I stopped using it. If we need a more moisture resistant filler we use a short...
    4 replies | 77 view(s)
  • Len's Avatar
    01-23-2022, 11:18 AM
    I've used a couple of different Iwata guns but not that model. The ones I used seemed to be decent but I preferred other guns.
    1 replies | 60 view(s)
  • Len's Avatar
    01-21-2022, 02:41 PM
    If anything is wrong with that it would be the tank size not the CFM. If you can hook it to a larger tank (minimum 30gal.) you might be ok. A lot...
    2 replies | 45 view(s)
  • Len's Avatar
    01-21-2022, 01:15 PM
    Len replied to a thread Seal Coat in General Discussion
    Gee I thought it was cold here in NJ, 11 last night but I can still get my shop warm enough to paint. Packers are my second most favorite team...
    29 replies | 741 view(s)
  • Len's Avatar
    01-21-2022, 08:41 AM
    The Scott Towels should be fine for using with grease and wax remover just be sure to use a "tack cloth" to do a final wipe right before spraying.
    2 replies | 67 view(s)
  • Len's Avatar
    01-20-2022, 07:37 PM
    Another variable that complicates polishing is that sanding with a fine grit can hide deeper scratches then polishing can fill the scratches with the...
    34 replies | 9613 view(s)
  • Len's Avatar
    01-20-2022, 03:46 PM
    Len replied to a thread Seal Coat in General Discussion
    That's right, low temps can sure mess things up. If you're doing one panel at a time you can use a heat lamp to get it warmed up.
    29 replies | 741 view(s)
  • Len's Avatar
    01-20-2022, 05:39 AM
    I don't see it in other pictures. Take a picture from further back so we can see where this is located. Edit: That metal look like it's in...
    27 replies | 492 view(s)
  • Len's Avatar
    01-19-2022, 02:18 PM
    Len replied to a thread Seal Coat in General Discussion
    You should be using the right size fluid tip in your spray gun for the products you're spraying. Most high build primers you'll want something...
    29 replies | 741 view(s)
  • Len's Avatar
    01-19-2022, 08:23 AM
    Len replied to a thread Seal Coat in General Discussion
    In most cases the paint manufacturer will recommend the proper reducer for the temperature but our shop usually varies with the product being...
    29 replies | 741 view(s)
  • Len's Avatar
    01-18-2022, 09:08 PM
    I normally drill them out with a spot weld bit but depending where they are you may be able to use a standard drill bit if you don't mind damaging...
    27 replies | 492 view(s)
  • Len's Avatar
    01-18-2022, 08:32 PM
    That 2" piece should be removed or repaired. It appears that you may be able to remove it and leave the end where the grove is then weld in a new...
    27 replies | 492 view(s)
  • Len's Avatar
    01-18-2022, 03:46 PM
    I would cut out the bad metal then weld in a backing strip then lay a new piece of metal on the backing and either weld or bond it to the backing...
    27 replies | 492 view(s)
  • Len's Avatar
    01-18-2022, 11:57 AM
    I have a different approach.... I never blast sheet metal unless it's just for a pitted rust spot because it's very easy to warp the metal. I...
    27 replies | 492 view(s)
  • Len's Avatar
    01-18-2022, 09:16 AM
    In warmer but especially in colder weather a heatlamp is a VERY important tool. We use these lamps almost every day to move the work along. LINK
    0 replies | 84 view(s)
  • Len's Avatar
    01-18-2022, 08:05 AM
    Blasting and priming will work if the rust hasn't gone through the metal. In that case you can blast prime then apply body filler to level the...
    27 replies | 492 view(s)
  • Len's Avatar
    01-17-2022, 07:25 PM
    Are you dealing with a local body shop supplier? If so you should be able to go and look at some paint chips but if not go to...
    4 replies | 131 view(s)
  • Len's Avatar
    01-17-2022, 05:38 PM
    Len replied to a thread Army Truck in General Discussion
    This Truck is going to take all Winter to complete. The body work is finished now it's all paint work.
    9 replies | 711 view(s)
  • Len's Avatar
    01-17-2022, 05:31 PM
    Len replied to a thread Army Truck in General Discussion
    OK so we've been working on the Army Truck in between other jobs. We've started by prepping and painting some removable parts so I thought I'd post...
    9 replies | 711 view(s)
More Activity
About Len

Basic Information

Signature


Statistics


Total Posts
Total Posts
45,856
Posts Per Day
7.76
General Information
Join Date
11-23-2005
Referrals
28