• Len's Avatar
    Yesterday, 05:47 PM
    Len replied to a thread plastic parts in General Discussion
    I haven't used all the different adhesion promoters but I know that some are good and some are not so good. I know that Glasurit, RM and Evercoat...
    see more
    6 replies | 75 view(s)
  • Len's Avatar
    05-18-2013, 09:43 PM
    Len replied to a thread COLOR SAND in Final Touch
    A 3" polisher works well in tight spots but other than that you can try to dampen a piece of soft cloth, apply a little Mystic Cut and hand rub. ...
    see more
    30 replies | 818 view(s)
  • Len's Avatar
    05-18-2013, 09:33 PM
    Len replied to a thread plastic parts in General Discussion
    The bare plastic parts can be scrubbed with a scuff pad and warm soapy water then wiped down with a decent grease and wax remover. I would probably...
    see more
    6 replies | 75 view(s)
  • Len's Avatar
    05-18-2013, 09:52 AM
    Len replied to a thread Thanks everyone in General Discussion
    She'll have fun driving that.
    see more
    3 replies | 82 view(s)
  • Len's Avatar
    05-18-2013, 09:49 AM
    Len replied to a thread new car orange peal in Final Touch
    Some have a lot more orange peel than others. Even the same make, model and color can vary quite a bit.
    see more
    8 replies | 73 view(s)
  • tr6oldtimer's Avatar
    05-17-2013, 10:21 PM
    tr6oldtimer replied to a thread new car orange peal in Final Touch
    Thanks Len, now to find a BMW in the hood to hone my skills :-) Maybe best to just leave alone, or trust to a pro.
    see more
    8 replies | 73 view(s)
  • Len's Avatar
    05-17-2013, 09:59 PM
    Len replied to a thread new car orange peal in Final Touch
    The trick with most OEM finishes is to NOT try to make them perfect, only improve them to "acceptable" by going with a fine wet grit like 3000 or...
    see more
    8 replies | 73 view(s)
  • tr6oldtimer's Avatar
    05-17-2013, 08:45 PM
    tr6oldtimer started a thread new car orange peal in Final Touch
    So you drop good money on car, and the finish sucks. Lexuz, BMW, others, it does not matter, most finishes are terrible. I have a 2012 Z4 silver...
    see more
    8 replies | 73 view(s)
  • another2centsworth's Avatar
    05-17-2013, 07:49 PM
    another2centsworth replied to a thread DuPont Basemaker confusion in General Discussion
    If its 85 out I go 95 on the reducer/basemaker. Stay a step up/slower but make sure you don't rush. :yikes Give good flash times. [)
    see more
    8 replies | 307 view(s)
  • another2centsworth's Avatar
    05-17-2013, 07:38 PM
    another2centsworth replied to a thread Need help with rustoleum flat black. in General Discussion
    I'd let it sit for a week or so to cure out better. Rescuff and go with light to medium coats as this is what what you need with that stuff. Read the...
    see more
    6 replies | 110 view(s)
  • Len's Avatar
    05-17-2013, 05:01 PM
    Len replied to a thread Plastic Bumper Cover Prep in General Discussion
    Depending on the paint products you're using a flex additive can make the finish quite difficult to polish after sanding. We usually paint the...
    see more
    5 replies | 79 view(s)
  • MARTINSR's Avatar
    05-17-2013, 03:07 PM
    MARTINSR replied to a thread panel bonding adhesive in Tools Used in the Body Shop
    Pre-drill the holes before you paint and bolt it on there properly. Listen, I am a big proponent of the structural adhesives in the industry. Are...
    see more
    2 replies | 186 view(s)
  • Len's Avatar
    05-17-2013, 11:20 AM
    Len replied to a thread Plastic Bumper Cover Prep in General Discussion
    If it's a flexible surface and you want it to hold up well then use a flex additive mixed with your hardened primers and paints.
    see more
    5 replies | 79 view(s)
  • Len's Avatar
    05-17-2013, 11:17 AM
    Len replied to a thread Need help with rustoleum flat black. in General Discussion
    Almost any paint looks good when first applied, it's a year or two down the road that tells how good it is. Also some less expensive products can be...
    see more
    6 replies | 110 view(s)
  • Len's Avatar
    05-17-2013, 10:54 AM
    Len replied to a thread Large Flake in General Discussion
    If it's an acrylic urethane and a medium hardener was used and the temperature is 65 degrees F or higher I'd say you can probably do your initial...
    see more
    14 replies | 443 view(s)
  • Len's Avatar
    05-17-2013, 09:52 AM
    Len replied to a thread Painting Hinges in General Discussion
    That's exactly what we would do with door hinges.... Clean the bare metal well then epoxy prime and paint, no need for sanding. They won't be quite...
    see more
    2 replies | 61 view(s)
More Activity
About another2centsworth

Basic Information

About another2centsworth
Biography:
Been self employed for 17 yrs.
Location:
In The Shop
Interests:
Family,Paint and Body,Boating,& Camping
Occupation:
In, around or associated in the same type busines for 32 years

Signature


[SIGPIC]

Statistics


Total Posts
Total Posts
3,463
Posts Per Day
2.21
General Information
Last Activity
05-17-2013 07:50 PM
Join Date
02-05-2009
Referrals
0

43 Friends

  1. Wydir Wydir is offline

    Senior Member

    Wydir

  2. ymurf ymurf is offline

    Senior Member

    ymurf

  3. zmanak zmanak is offline

    Member

    zmanak
Showing Friends 41 to 43 of 43
Page 5 of 5 FirstFirst ... 345