Tab Content
  • Phil V's Avatar
    Yesterday, 08:21 AM
    Phil V replied to a thread fender welt install? in General Discussion
    Are they pre-drilled ?
    see more
    3 replies | 59 view(s)
  • Phil V's Avatar
    06-09-2013, 10:51 AM
    Phil V replied to a thread Sharpe planitum in Tools Used in the Paint Shop
    I think different guns fit different people better. The Sharp Platinum was a great beginner gun but as stated was really S- L- O- W. Which again...
    see more
    54 replies | 2841 view(s)
  • Phil V's Avatar
    06-09-2013, 10:17 AM
    Phil V replied to a thread painting a bass boat in General Discussion
    I usually spray 2K primer at the end of the workday and start sanding it the next morning. (I'm talking relatively large areas, not small spot prime...
    see more
    8 replies | 131 view(s)
  • Phil V's Avatar
    06-08-2013, 10:33 AM
    Phil V replied to a thread 99 Corolla in Collision Repair
    I just run the parts prices at my cost for new aftermarket parts --- Hood is right around - $100 Fender $ 45...
    see more
    8 replies | 201 view(s)
  • Phil V's Avatar
    06-07-2013, 01:47 PM
    Phil V replied to a thread 99 Civic Coupe Sideswipe in Collision Repair
    That is really not that bad of a job to do. First of all before you get serious about buying the car - how many miles does it have on it ? That car...
    see more
    21 replies | 355 view(s)
  • Phil V's Avatar
    06-07-2013, 11:02 AM
    Phil V replied to a thread Rear Damage, good buy or not?? in Collision Repair
    I agree with Mike. Keep in mind that there is a REASON why the insurance company totalled the car (salvage title). There is no possible way to...
    see more
    15 replies | 345 view(s)
  • Phil V's Avatar
    06-07-2013, 10:47 AM
    Phil V replied to a thread Next step in General Discussion
    That's a tough question to answer because there are lot of variables involved. As a rule epoxy is never block sanded. That is " as a rule" because...
    see more
    2 replies | 95 view(s)
  • Phil V's Avatar
    06-07-2013, 10:41 AM
    Phil V replied to a thread painting a bass boat in General Discussion
    I agree with Len. Painting wet on wet using 2K primer is not recommended for a couple different reasons. First is that the 2K tends to shrink more...
    see more
    8 replies | 131 view(s)
  • Phil V's Avatar
    06-07-2013, 10:32 AM
    Phil V replied to a thread Masks resperators in Health, Safety & Rules
    Len, I understand what your saying I agree with you up to a point. But I really believe that the reason paint manufacturers and mask manufacturers...
    see more
    7 replies | 328 view(s)
  • Phil V's Avatar
    06-07-2013, 04:00 AM
    Phil V replied to a thread Masks resperators in Health, Safety & Rules
    I have been spraying paint professionally in paintbooths and in home garages for 40 years and I have always used disposable dual charcoal cannister...
    see more
    7 replies | 328 view(s)
No More Results

1 Visitor Messages

  1. DaddyCat
    View Conversation
    http://www.autogeek.net/bo6040.html
    This ad is the reason I thought the Makita BO6040 Polisher would do the job but maybe the slow rpms 180 - 670 makes it not capable of polishing out 3000 grit sanding scratches. I value your opinion Phil
    kind regards, Joe
Showing Visitor Messages 1 to 1 of 1
About Phil V

Basic Information

About Phil V
Biography:
I have many hobbies
Location:
lower Michigan
Occupation:
Prof. Autobody and paint

Statistics


Total Posts
Total Posts
6,807
Posts Per Day
2.46
Visitor Messages
Total Messages
1
Most Recent Message
05-21-2010 08:27 AM
General Information
Last Activity
Today 01:36 AM
Join Date
11-24-2005
Referrals
1